ReNew Archives - Page 13 of 16

I hope you will take a moment to view how I test drove my Dremel Trio. This is seriously a really fun power tool! Just be sure you are safe so as not to ruin the fun. Eye protection, face mask, and ear plugs. Check.

For those of you who like to skip to the end of the book and see the ending, here you go:

For the rest of you, here is how I created this cut out/back lit bookshelf that started life as a bookshelf from a closing Borders bookstore.

Tutorial for creating a cut out bookcase:
Almost any bookcase will work for this project, but the ones that have a thin wood (can be masonite) backing will work best. Set up a work area that you don’t mind getting dusty and dirty. Remove the shelves from your bookcase.

Cutting the endcap:

Materials:

circular saw
level
clamp
scrap wood
screws
drill

I cut the endcap in half lengthwise so I could use half for each end of my bookshelf, and to position it flush against the wall. To cut a straight line using a circular saw, I clamped one end of a level to the endcap. My level wasn’t long enough, so I drilled a scrap piece of wood on top of the level and into the end cap to support the other end.

I set the circular saw blade just below the depth of the endcap. By resting the endcap on two 2×4″ boards, I was able to creative a gap below the endcap for the sawblade to pass through.Then I ran the circular saw along the level for a straight cut. Straight as an arrow, and it met Pretty Handy Dog’s approval.

Cutting out the backing design and painting:

Materials:

Dremel Trio
Palm sander
Sandpaper (100 grit & 220 grit)
Scrap 2×4 lumber
Chalk or pencil
Wood putty
Putty knife
Primer
Paint (white and navy blue)
3M Clean Edge technology painter’s tape
Newspapers
2″ paint brush
Small paint roller and tray

Sketch out the design on your bookshelf (using chalk or pencil) before beginning.

Before using any new power tool, take some time to read through the manual.

To insert a bit into the Dremel Trio, you push in the blue (shaft lock) button on the front and use the enclosed wrench to loosen the collet nut on the tool.

Insert the cutting bit into the Trio. (The trio also comes with a sanding drum bit and a routing bit!)

Tighten the collet nut with the wrench.

Turn the blue handle on the side of the TRIO to raise or lower the base plate.

Adjust the base plate until the cutting bit extends slightly below the wood backing of your bookcase.

Lay the bookcase down on its back. Position 2×4 boards under the edges of the bookcase (or you will be cutting into concrete. I’m pretty sure the TRIO is not capable of that, but I could be wrong.)

Plug in your Trio and get ready to have some FUN! You may want to practice on a scrap piece of wood before working on your bookcase. The TRIO allows you to change directions quickly and easily. Creating fanciful cuts is a breeze!

Squeeze the trigger and when the bit reaches full speed you can plunge it into the workpiece. For the pin holes hold the Trio steady, insert the bit and then lift it back out of the same hole.

To cut trees and other designs, plunge the TRIO into the wood and then slowly move the tool through the wood to carve your design. Be wary of long “V” shape cuts as they will make the backing weaker.

When your design has been completed, use the power sander to sand the back of the bookcase (where the majority of the splintering will have occurred.)

Insert the sanding drum bit into the TRIO and sand any large cut out areas.

Fold a piece of sandpaper in half and feed it through the thin lines of the branches to sand any rough edges that can’t be reached with the sanding bit.

Set the bookcase upright and inspect the cuts for more splinters. You can preview what your design will look like when lit up. Lookin’ good, huh?!

Before sanding the rest of the bookshelf, repair any dents or holes with wood putty. (This is a post I wrote about repairing all types of holes if you need help.)

Use the palm sander and a fine grit (220 grit) sandpaper to rough up the rest of the bookshelf.

Apply a coat of primer to the bookcase, shelves and sides. (Still working on emptying that can of KILZ Clean Start primer! Love that stuff.

When the primer has dried, mask off the sides of the bookcase where they meet the back.

3M sent me this Scotch Blue Painter’s tape with Edge-Lock protector to try. I was skeptical, but when I pulled the tape off it did give me a clean edge. The only place I had a little bit of seepage was in the corners where I didn’t press the tape tightly into the corner. The key to using this tape is to firmly press the edges with your finger to engage the “Edge-Lock” seal. I haven’t tried it for painting walls, but you better believe I have a wall project coming up that I can try it on.

Paint the back of your bookcase. I chose a very dark navy blue. To save paint, I used a medium blue paint for my first coat to darken the back and hopefully save paint.

Then paint one coat of the navy blue.

Follow up with a second coat to eliminate any streaking.

When the navy paint has dried, tape along the edges of the navy blue backing, where it meets the sides. Slip pieces of newspaper underneath to catch any paint splashes. (Will you get a load of my lazy supervisor! You think he’s been working hard in the heat? Uh no, that would be me doing all the work and him snoozing away the day.)

Paint the rest of the bookcase, the sides and the shelves white. I used two coats of Benjamin Moore Impervo Semi-gloss white.

Once the paint has dried completely, re-assemble the bookcase. And screw the end cap halves onto either side of the bookcase.

I installed a light rope behind the bookcase (tutorial to come at a later date) and set the lights on a timer. The rope light comes on at dusk and illuminates all the cut outs.

There is a very soft glow emitted from the back of the bookcase.

It provides the perfect amount of light for my son who HAS to have a light on at night.

My only complaint about the rope lights is that they give off a strong plastic odor. But, after a week the smell has dissipated.

I had the foresight to purchase a few of the clear display stands that slide into the end caps of the bookcase. It makes it easy to display books to pique my son’s reading interests.

Oh look! There he is now! Mission accomplished, reading interest piqued. Yes, I think he is double-jointed and a teacher pointed out that both my son’s sit like that. Must be in the genes.

A few more detailed pictures of the bookshelf. This has to be one of my favorite projects I’ve created recently. And it wasn’t very difficult to complete.

June 25, 2011/407 Comments/by Brittany Bailey

Before and After, painting, Painting & Antiquing Techniques, priming, ReNew, Upcycling

Painting a Bamboo Rug

Back story and my ramblings:

Sleeping outside on the screen porch was nice until I woke up with a sore neck. So, I won’t be doing that again for a while. But, I won’t complain because we are lucky to have a screened porch and I am really loving it after the recent makeover.

The makeover was spurred on by this Pier One bamboo rug that I scored for $25 while thrifting!

It’s nice isn’t it? Especially with the splashed paint on it. Yes, I was the sloppy culprit who dripped paint while repainting my garden bench. But, no big deal, I had bigger plans for that rug.

So I sat down at my computer and spent a few ~~minutes~~ hours on Pinterest to research some patterns for my rug – seriously addictive site! But, it is also proving to be a huge organizational tool for my blog. I can pin ideas I want to create. Or I pin other bloggers projects that I want to make sure I give credit to when I ~~steal~~ borrow their ideas.

Once I narrowed down the designs I liked, I used my photoshop skills to change color palettes and design to create a sketch for my painted rug.

Then I ran over to Ace Hardware to purchase some paint. I ran into my good buddy, Mr. Paint Dept Guru – and guess what he did! He told me he had just finished going through the mistinted cans and hadn’t even priced them so he let me have my pick of some cans for….FREE! That is why I love my Ace Hardware. They are a small neighborhood store and all the employees know my face. The cashier and I even have a running joke. She couldn’t remember my name once (how can she, there are only 300 customers in there a day), so I told her that I’d give her a hint. I told her that I share the same name with a famous pop singer. She laughed and said, well, I keep thinking Beyoncé but I know that isn’t your name. So, now she calls me Beyoncé everytime I walk in.

Tutorial:

If you just came here to find out how I painted the rug, I’m sorry about my story-telling. Anyway, here is the tutorial, you found it!

Materials:

Kilz Clean Start Primer
Stir stick
Drop cloth
ScotchBlue Painter’s Tape
Gloves
Paint brushes (thin and thick)
Paint roller
Butcher paper
Chalk
Scissors
Latex paint colors
Minwax Polyurethane
~~Mask~~ Yeah! No need to wear a mask with the new KILZ clean start primer!

The good people over at KILZ recently sent me a gallon of their new eco-friendly primer* (yeah, I thought that was an oximoron too.) I’ve used KILZ 2 latex primer for years and have been very happy with the product, so I had serious doubts that some “green” primer could perform the same. Well, I stand corrected! Love this stuff!!! No face mask necessary, no need to worry about off gassing. The primer had no smell that I could determine.

And it sticks like glue to the surface that needs to be primed. It worked just as well as the regular “stinky” primer. I even scouted out my local Home Depot to see if they stock it (for when I run out) and they do! (My local Lowe’s hasn’t received a shipment yet.)

Just in case you didn’t see this: Zero VOCs!!! I like that!

Sorry, I get side tracked easily.

Start by laying down a drop cloth and putting on rubber gloves.

Stir your primer well. Roll on the primer onto the bamboo rug.

Then smooth the primer in the direction of the slats with a brush.

Tape off the inside edge of the canvas border using your painter’s tape.

Roll on the border color. Yup, that pretty blue gray paint was a mistint and therefore FREE!

After the border color dries, remove the painter’s tape and then put tape on top of the border.

Roll on the base color for your rug. Then use a brush to drag the paint between the slats. You may need to apply a second coat of paint.

Using the chalk and butcher block paper, draw out your rug design.

And lay the design on top of the rug.

Cut out the largest shapes first. And trace inside the cut outs onto the rug.

Paint inside the chalk lines with the flower color.

Next draw the vines and branches onto the rug using chalk. Chalk can easily be wiped off if you wish to work with the design a little bit.

Continue tracing flowers, vines and leaves and fill them in with paint.

When your rug is completely painted and dry, wipe it off with a damp rag. Then roll on at least 2 coats of water based polyurethane. I prefer Minwax, but use what works for you.

One word of advice when painting on bamboo slats. Don’t try to be a perfectionist. Just relax and have fun. The inconsistencies will make your rug look more authentically hand-painted!

I love my new porch rug! Even better, I love the price!

It looks fabulous with my beachy coffee table I made last year.

I promise – a photo tour of our screen porch will be coming soon.

* Disclaimer: I was sent a gallon of Kilz Clean Start Primer for my honest review. I was not paid or compensated for the review other than with a gallon of primer. My thoughts and opinions are authentic and my own. In other words, I respect you and will not lead you astray with false product information.

Sharing this project with:

June 7, 2011/66 Comments/by Brittany Bailey

arts and craft, Birdhouse, Crafts, Gift Ideas, ReNew, Trash to Treasure

Birdhouses with Style

Our preschool silent auction is today. Every year I donate a one-of-a-kind birdhouse to be auctioned off. I never spend more than $3 on the birdhouse and usually buy the unpainted versions at Michael’s or ACMoore. Then I get creative by hand-painting a scene and add unexpected touches to the house – thus creating birdhouses with style.

2008 – Jardin da Girasoli de Vendere “Vendor of Sunflowers”

Painting sunny sunflowers and some green grass gave this birdhouse a sunny garden look. I added a gold spigot for the new perch. Using a spade bit in my drill, I cut a hole slightly smaller than the spigot, then simply screwed the spigot in place. For added stength I coated the threads with some E-6000. Can anyone guess what the roof tiles are made from? They are canvas shims! Those are the freebie scraps if wood that come with a painter’s canvas! Painting them bright red took the little birdhouse from cute to bidding war worthy!

2009 – Red & White Bird Silhouette Round House

I apologize right now for the condition of this picture! Obviously this is the only picture I took of this cute little abode. The birdhouse was a $2 find at my local Goodwill. The roof was detaching and it was painted an ugly 90’s hunter green and burgundy. I gave the house a good cleaning, then glued and nailed the roof back on. After a fresh coat of primer and white paint, I hand-painted the bird motif and the roof and base. The perch is a curtain rod screw (that holds the rod in the curtain rod bracket). Then she received a little green ribbon and a silver bell on the top. So simple, but one of my favorites!

2010 – Christmas Time, Snow and a Pinecone Roof

Another unpainted house picked up at Michael’s. This house got some serious head turning attention with a pinecone plank roof, white snow, glitter, and a stick for a perch. The tutorial to make this birdhouse can be found here.

The back has a large Christmas tree decorated for the holidays. I hope the birds appreciate it.

To protect all my birdhouses from the elements (should they really be “for the birds”), I coated them with a few coats of polyurethane.

I know that some of you might be thinking you can’t do this, but let me float some ideas for you. Instead of decorative painting try:

Mod Podge Wallpaper on the sides
Mod Podge Fabric to the sides
Use a stencil
Search the web for picture inspiration and trace it onto your birdhouse.
Use painters tape to create stripes
Let your little ones decorate the house with paint

So, how much do you think my pinecone roof birdhouse will fetch today? I hope more than $3!

November 20, 2010/12 Comments/by Brittany Bailey

Build It, Easel, Ladder, ReNew, Stashbusting

Ladder Stepping Up to the Stashbusting September Challenge

Robin over at TheTshirtDiaries is a gal after my own heart.

She has thrown down a challenge to anyone willing to close up their pocketbooks this month (well, at least for spending on arts and crafts and DIY projects), and use what you have in your home, workshop, craft room or wherever you create. The challenge is called Stashbusting September and you can read more about it here.

She also has a link party called Upcycled Awesome every Wednesday. I hope you hop over to check out some of the fantastic ideas she and other bloggers have shared.

I am always up for a challenge, so I jumped in with both feet ready to complete some projects and do it without spending a dime!

Obviously toe-less shoes are not safe in the workshop, unless you want to be,
ummm toe-less!

So, what about you? Up to the challenge? I hope you step up to the plate and try your hand at re-using and making-do with what you have on hand! Altogether now: Hey ho, let’s go!

Here is one of the projects that has been sitting around waiting to be given a new life. An old ladder that I picked up from The Habitat for Humanity ReStore (visit this post for more details).

$15 dollars was a little more than I wanted to pay, but Habitat for Humanity is one of my favorite charities, so I don’t mind spending a little more when the money goes to people who need housing.

I actually made this ladder into two separate items. I’ll show you the results of the other half when I finish that project.

Tools Needed:

Safety Goggles (Definitely wear your safety goggles when using a pry bar!)
Hammer
Sand paper or sanding block
Pry Bar
Drill
Screws
Piece of L-shaped moulding

I used the chisel end on my pry bar to loosen the rivets. Some of those rivets were hanging in there and weren’t ready to come out yet. But, I showed them who’s boss. That would be me, the woman in a skirt and toe-less sandals!

Then used the claw end of a hammer to to remove it the rest of the way.

After removing the brace and top rivets, the ladder’s front and back were free from each other forever. I wiped the whole ladder down with a damp cloth and then lightly sanded it to remove any splinters.

I played around with the back of the ladder in our dining room…

…but ultimately decided I wanted to use it as an easel.

I have a decent scrap pile with leftover boards and trim pieces. A little scrap of L shaped moulding was exactly what I needed.

I measured how high I wanted the moulding to be and then marked where my screws would go.

I predrilled the holes.

Leveled the moulding and screwed it into the ladder.

Instant easel!

Love it! Especially those paint splotches.

It looks great next to our repainted Craig’s List buffet and hutch.

Plus, I can change out the artwork on a whim.

I hope this has inspired you to do some Stashbusting this month. Check out what some other Stashbusting bloggers are doing this month: HERE!

September 9, 2010/31 Comments/by Brittany Bailey

Chalk marker, Chalkboard paint, Crafts, distressing, painting, Painting & Antiquing Techniques, ReNew

Chalk it up…to a busy day.

…to another busy day in the life of Pretty Handy Girl!

I had fully intended on posting a tutorial on distressing furniture for you today. But, I got side tracked today and then let’s just say that my evening ended up with a visit from these guys:

Thank you Raleigh Fire Department for putting out my oven fire!

Let me tell you, it is a scary thing to see your heating element turn into a 4th of July super-sized sparkler! Luckily no one was hurt and our kitchen is still white (not smoky gray.) Needless to say, we will be in the market for a new oven this week. Any recommendations or “steer clears” would be appreciated. And a word of advice, if your heating element shorts out, sparks and catches fire, turn off your circuit breaker.

Not exactly what I planned on dealing with today! I did have plans for one tiny little project. This little project had me on a hunt for the illusive and extremely rare chalk marker. I have been looking everywhere for one of these exotic creatures.

Target – nope

Walmart – nope

Ace Hardware – nope

JoAnn’s Fabrics – nope

Jerry’s Art-a-rama – Ding, ding, ding! Finally found it!

If you’ve been around the blogosphere lately, you have seen chalkboard paint projects everywhere! I probably wouldn’t be surprised to see a chalkboard painted dog next week.

I had some leftover chalkboard wall decal material, so I cut a little label for our jar of colored pencils. But, I really wanted a chalkboard marker so I could write on the label and not worry about it smudging from little hands using it daily.

So, naturally after using my new chalkboard marker and LOVING IT! I decided to paint some more things with chalkboard paint and use my new marker.

I put up my homemade spray tent (I’ll have to show you how I made it later.)

And got busy. My mind played “Back in Black” in my head as I sprayed. (Any other AC/DC listeners out there?) I decided to use automotive black primer (for better adhesion on the plastic spice lids.)

First up where these Goodwill candy jars all four and the rack for $6.99!

U-G-L-Y oak lids, but not for long…

Blackified, labelled and now looking good.

Next victim was a spice rack and jars (I’m embarrassed to say)
that I repainted years ago.

That’s right, back in the sponge-era.
The gold ink labels are impossible to read.

I carefully lined them up and made a list of the order

they were in to make re-labelling them easy.
Seemed like a great idea, UNTIL my oven caught fire.
Then I swept everything off the counters and away from the stove.