8. Complete with "L" brackets on corners. Add gifts and deliver!

DIY Sheet Metal Gift TraysDIY Sheet Metal Gift Trays

The holidays are fast approaching and it’s time to start thinking about gift giving ideas! Gift trays are a great way deliver gifts to your friends, neighbors or teachers. The best part of a gift tray is it can be reused for anything they want and nothing goes to waste! Follow along with this tutorial to see how to make these DIY Sheet Metal Gift Trays.

Materials:

(I’ve included affiliate links for your convenience. I earn a small percentage from a purchase using these links. There is no additional cost to you. You can read more about affiliate links here.)

Materials: Sheet Metal Gift Tray

Instructions:

Cut your piece of plywood to the desired size for the tray base. Lay the plywood base on top of the sheet metal and trace with a permanent marker. Use tin snips to cut the metal to size.

1. Cut base and mark sheet metal size.

Put on your safety gloves and use the sanding block to remove some of the shine from the sheet metal. Smooth over any sharp edges.

2. Sand Sheet metal edges and base.

Rub the steel wool over the entire sheet metal piece to give it a soft polished finish.

4. Use steel wool to dull sheet metal surface.

Load a tube of construction adhesive into your caulk gun. Apply a fair amount of adhesive to the plywood. Glue the sheet metal to the top of the plywood.

5. Add Construction Adhesive to wood base

Press the sheet metal down evenly on top of the adhesive. Wipe off any excess if needed with a paper towel.

6. Press sheet metal on top of wood base.

Cut the 2″ pieces of lathe or scrap moulding to the length of the two shorter sides. Next, measure and cut two pieces of lathe for the long ends. (Be sure to allow extra length to overlap the short pieces of lathe/moulding.  Use the construction adhesive and brads to secure the lathe to the sides of the plywood. Clamp the sides until the adhesive cures.

8. Clamp sides while glue cures.

Once the adhesive is cured, remove your clamps. Attach the L brackets on the lower half of each corner using 1/2″ wood screws. The L brackets will reinforce the sides and add an industrial look.

9. Add corner brackets for extra support and decoration.

There you have it! These DIY Sheet Metal Gift Trays are easy to make, look great, and are an extra special and environmentally-friendly way to give gifts!

10. Add gifts and deliver!

I hope you love this project. Do you have other ideas for quick gift giving? Please share!

signature

Want some more gift giving inspiration?

DIY Scrap Moulding Trays

scrap-moulding-trays

Make a Driftwood Gift Crate

Make a Driftwood Gift Crate | Pretty Handy Girl

Gold and Marble coasters | Scrap wood | contact paper

Hello Pretty Handy Girl fans!! I am Anika – the girl behind Anika’s DIY Life. As a long time Pretty Handy Girl fan myself, I can’t find words to tell you how excited I am to be a contributor to Brittany’s amazing site and share my projects with you amazing readers every month! You can read more about me here but in a nutshell, I love everything DIY – from building furniture to easy crafts. I also love color, bling and saving money. You will find at least one of these in every project of mine! Today’s project is all about bling and saving money – easy gold and marble coasters.

Gold and Marble coasters | Scrap wood | contact paper

Don’t you love the look of marble and gold together? Here is a secret: it’s not really marble, it is contact paper! I discovered the awesomeness of contact paper when I needed a solution to update the countertop in the kids bathroom of our rental. The contact paper is still holding up perfectly after 5 months. I had half a roll left and have been looking for ways to use it up. I decided it would be fun to make a “marble” tray and these fun gold and marble coasters!

Materials:

(I’ve included affiliate links for your convenience. I earn a small percentage from a purchase using these links. There is no additional cost to you. You can read more about affiliate links here.)

Instructions:

Step 1 – If you are using precut wood tiles, you can skip directly to the painting step. If not, cut out the hexagon template and use it to trace the hexagons on your piece of scrap wood.

Gold and Marble coasters | Scrap wood | contact paper

Step 2 – Using a jig saw, cut out your hexagon shapes.

Gold and Marble coasters | Scrap wood | contact paper

Step 3 – Sand the faces and edges smooth. It is important to get rid of all the saw marks because you won’t like how they look on the edge of the coaster once painted (ask me how I know. 😉 )

Gold and Marble coasters | Scrap wood | contact paper

Step 4 – Give your coasters a coat of spray primer followed by a few coats of gold spray paint. If you need help deciding which gold spray paint you need, here is a fantastic gold spray paint comparison guide for you!

Gold and Marble coasters | Scrap wood | contact paper

Step 5 – Decide the placement of the “marble” and cut the contact paper pieces accordingly (leaving a bit of overhang on the sides.) Slowly apply the contact paper while smoothing out any air bubbles.

Gold and Marble coasters | Scrap wood | contact paper

Step 6 – Using the x-acto knife, cut off the excess contact paper from the edges.

Gold and Marble coasters | Scrap wood | contact paper

Step 7 – Add non-stick felt pads to the back side. If you want to be totally frugal like me, you can use squares of scrap felt and super glue them to the back. (Pssst… see the back? that’s why you have to sand them really well!)

Gold and Marble coasters | Scrap wood | contact paper

Here’s a video to show you how easy it is to make these marble and gold coasters:

That’s it! You have a gold and marble coaster set. I decided to get whimsical with the gold and marble pattern. You can get totally creative with the shapes of marble and gold on the coasters. Each coaster will be different yet eye-catching!

Gold and Marble coasters | Scrap wood | contact paper

Tie four together with some twine to make a pretty hostess gift!

Gold and Marble coasters | Scrap wood | contact paper

Hope you enjoyed this project! I will be back again next month with another fun project! In the meantime visit Anika’s DIY Life for more fun DIY projects.


~ Read More of Anika’s Tutorials ~

 

Pin for later!

Easy Gold and Marble Coasters | Pretty Handy Girl

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Hi all, Pretty Handsome Guy here filling in for Brittany. Last night Brittany and I were wrapping presents and I thought I’d share with you some common gift wrap problems and how to deal with them.  Think of this as the polar opposite of her Creative Gift Wrapping series of posts.

The Squish and Tape and Tape and Tape

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Do you ever end up with a present that hangs out of the wrapping paper?

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

No problem, simply squish the gift inside the packaging as far as you can…

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

…and quickly fold over the end and slap on some tape. Then use some more tape to close the gaps,

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

and just for good measure add some more tape. Hey, tape is cheap, no need to be stingy with it!

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

All done, and the goal of hiding the present has been achieved!

The Panel (not to be confused with the type of pants pregnant women wear.)

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

How many times have you cut your wrapping paper only to realize that it is too short to go around the package? When it comes to wrapping presents I adhere to the adage “measure never, just cut it”.  I mean seriously people we aren’t building a house here, what you are wrapping is meant to be destroyed anyways.

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Here is the solution! It is called the panel. Simply cut another piece of wrapping paper the width of the gap (or maybe a little wider.)

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Tape it on (no need to match up the pattern, no one will see the bottom when it is under the tree.). Bonus points if you can manage to use 2-3 different types of wrapping paper – just tell everyone it is a “holiday medley”.

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Super easy solution and the best part is that you don’t have to go back and cut a whole new piece of wrapping paper.  The environment will thank you for this one.

The Nip, Tuck & Roll

Now we are down to one of the most common wrapping problems. What to do when you have too much wrapping paper on the ends of your package.  And yes I realize most of these “problems” are a function of not measuring in the first place but whatever.

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Normally I would simply roll the sides in until they meet the package, but in an effort to neaten things up a bit, you can simply gather the end in your hands and snip off the excess.

Now simply fold in the end towards the box.
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
Continue to roll the paper in…

…until you reach the box, then smash the end down with your hand to flatten it.

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
And tape your end down.
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
Done. Problem solved, any questions?
Adding a Gift Tag (bet you’ve never seen it done this way!)
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
I found the little key tags that Brittany bought for tagging her presents. Creative idea and all but sheesh a lot more work than a stick-on “To/From” tag.  But I devised a new way to attach them to the gift without ribbon.
Simply grasp a corner of your package and use a hole punch to make a hole in the gift wrap.
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl

Then take a piece of tape and twist it into what I call a “tapepick” (looks like a toothpick.)

Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
Thread the “tapepick” into the hole you made in your gift wrap.
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
Then grab another piece of tape and fold it over the ends of your tapepick to secure them.
Fixing Common Gift Wrap Problems | OMG! So funny, you have to read this. | Pretty Handy Girl
That’s it. Thanks for reading my post today. Hopefully Brittany will invite me back to show you how I make a bed in less than 10 seconds!
– Pretty Handsome Guy

Pin for later!

how to fix common gift wrapping problems

Quick & Easy Peppermint Oreo Recipe : Great for last minute cookie exchanges or gifts

 

Want a quick and easy holiday recipe you can make with the kids? When you don’t have time to bake, but you still want to give a homemade holiday treat, try this recipe for Peppermint Oreos!

Quick & Easy Peppermint Oreos

Ingredients:

  • 1 Pkg. of Oreo cookies
  • 1 Pkg. of peppermint candies
  • 1 Pkg. of white chocolate chips

Instructions:

Place the peppermint candies in a double ziploc bags. Let the kids hammer them to smithereens! (I placed scrap wood under the peppermints to protect the countertop.)

While the kids are pounding away to their heart’s content. Melt white chocolate chips in a double boiler (or in the microwave. But, the double boiler will keep the chocolate from hardening as fast.)

Pry the hammers from your kid’s hands. Place the crushed peppermints into shallow bowls (one for each child.)

Roll the edge of the oreo cookies into the white chocolate.

Then roll them into the crushed peppermints.

Lay the cookies onto wax paper to cool.

 

After they cool, eat them, gift them or save them for a snowy day.

A bunch of oreos would fit nicely in one of these decorated gift bags made from a cloth napkin, don’t you think?

drawstring gift bags made from cloth napkins

Want more 15 Minute Gift Ideas?

 

Happy Holidays!

 

Pin for later!

Want a quick and easy holiday recipe you can make with the kids? When you don't have time to bake, but you still want to give a homemade holiday treat, try this recipe for Peppermint Oreos! | Pretty Handy Girl #prettyhandygirl #oreorecipe #holidayrecipe

DIY Copper Ring Jewelry | Pretty Handy Girl

DIY Copper Ring Jewelry | Pretty Handy Girl

The holidays are here and you know what that means: It’s time to check off items from your gift list. I don’t know about you, but I detest braving the mall traffic and chaos. I’d much prefer to stay indoors and make gifts for the ones I love. Not only is it more peaceful DIYing gifts, but it saves money too! Why not make beautiful DIY Copper Ring Jewelry for the bling lovers on your list. Or you could use a ring or two and make a unique key chain fob.

DIY Copper Ring Jewelry | Pretty Handy Girl

I’m honored to be part of the Bernzomatic Torch Bearers program. Bernzomatic has sponsored this post to help you with your holiday gift ideas.

This fun project is sure to keep you warm and cozy with a little fire and heat using a Bernzomatic ST2200T Detail Torch.  The ST2200T is a great torch to start with if you’ve never used one. The small size fits in the palm of your hand and produces a small fine tip flame that’s perfect for jewelry making (among other small projects.)

DIY Copper Ring Jewelry | Pretty Handy Girl

To make the copper ring jewelry, you’ll need a few supplies. You can pick most of them up at your local hardware store or online.

DIY Copper Ring Jewelry | Pretty Handy Girl

Materials:

(I’ve included affiliate links for your convenience. I earn a small percentage from a purchase using these links. There is no additional cost to you. You can read more about affiliate links here.)

Instructions:

Use the pipe cutter to cut several rings (approximately 1/8″ thick) off the end of your copper pipe. You may need to cut several to get ones the same thickness. (For more details on how to use a pipe cutter, you can watch my video here.

DIY Copper Ring Jewelry | Pretty Handy Girl

Select the rings you wish to use for the necklace.

DIY Copper Ring Jewelry | Pretty Handy Girl

Use the metal file to file off any sharp edges on the copper rings.

DIY Copper Ring Jewelry | Pretty Handy Girl

Sand the edges until they are smooth (I turned my power sander upside down in a clamping table and turned it on while holding the rings onto the sandpaper to speed the process of sanding.)

DIY Copper Ring Jewelry | Pretty Handy Girl

Start by laying two rings side-by-side.

DIY Copper Ring Jewelry | Pretty Handy Girl

Apply a generous amount of flux to each ring where you wish to join them.

DIY Copper Ring Jewelry | Pretty Handy Girl

Start your Bernzomatic ST2200T torch and heat the rings where you added the flux.

DIY Copper Ring Jewelry | Pretty Handy Girl

As soon as the flux melts, touch the solder wire onto the spot where the flux was. (Make sure the rings are still touching. If not, nudge them back together with the pliers.) Hold the solder in place until it flows onto the copper rings.

DIY Copper Ring Jewelry | Pretty Handy Girl

Let the rings cool (or drop them in a container of cold water.)

DIY Copper Ring Jewelry | Pretty Handy Girl

Solder the next ring by following the steps above (add flux, heat, and solder.) If you mess up, you can reheat the solder to remove it and start over.

DIY Copper Ring Jewelry | Pretty Handy Girl

Curl a piece of copper wire to form a circle.

DIY Copper Ring Jewelry | Pretty Handy Girl

Cut off the copper circle.

DIY Copper Ring Jewelry | Pretty Handy Girl

Open the circle slightly. Add flux to the wire ends and the copper ring where you want to join them. Heat the area, let the flux melt and touch the solder to the ends of the copper wire. (This step may prove a little difficult to control the solder. If you are having trouble, try to add the solder to the copper ring, then guide the wire into the molten solder. Hold the wire in place with pliers until the solder hardens.)

DIY Copper Ring Jewelry | Pretty Handy Girl

To hide the shiny silver solder, use copper Rub n’ Buff on the joints. Or coat the entire necklace pendant with gold Rub n’ Buff for gold jewelry.

Feed a chain through the loop . . .

DIY Copper Ring Jewelry | Pretty Handy Girl

. . . or sew some suede leather cord to the loops.

DIY Copper Ring Jewelry | Pretty Handy Girl

Then sew clasps to the other end.

DIY Copper Ring Jewelry | Pretty Handy Girl

Behold beautiful new necklaces that you made yourself!

DIY Copper Ring Jewelry | Pretty Handy Girl

These necklaces would look great with any bohemian or casual outfits.

DIY Copper Ring Jewelry | Pretty Handy Girl

They are super fun to make and will surely delight anyone who loves jewelry.

DIY Copper Ring Jewelry | Pretty Handy Girl

What could you make with a Bernzomatic Torch and some copper pipe? The possibilities are only limited by your mind.

PHGFancySign

Disclosure: This is a sponsored post for Bernzomatic. As a Bernzomatic Torch Bearer, I was provided complimentary torches and was compensated for my time and efforts. I was not told what to write. All opinions are my own. I am particular about the brands I represent and will always let you know when you are reading a sponsored post.

Want more frugal gift ideas for the holiday season?

Tres-frugal_diy-gifts4

 

Pin for later!

This DIY copper ring jewelry is the perfect idea for a handmade gift! | Pretty Handy Girl #prettyhandygirl #giftidea #DIYgift #DIYjewelry