I hope you will take a moment to view how I test drove my Dremel Trio. This is seriously a really fun power tool! Just be sure you are safe so as not to ruin the fun. Eye protection, face mask, and ear plugs. Check.

For those of you who like to skip to the end of the book and see the ending, here you go:


For the rest of you, here is how I created this cut out/back lit bookshelf that started life as a bookshelf from a closing Borders bookstore.


Tutorial for creating a cut out bookcase:
Almost any bookcase will work for this project, but the ones that have a thin wood (can be masonite) backing will work best. Set up a work area that you don’t mind getting dusty and dirty. Remove the shelves from your bookcase.

Cutting the endcap:

Materials:

  • circular saw
  • level
  • clamp
  • scrap wood
  • screws
  • drill

I cut the endcap in half lengthwise so I could use half for each end of my bookshelf, and to position it flush against the wall. To cut a straight line using a circular saw, I clamped one end of a level to the endcap. My level wasn’t long enough, so I drilled a scrap piece of wood on top of the level and into the end cap to support the other end.


I set the circular saw blade just below the depth of the endcap. By resting the endcap on two 2×4″ boards, I was able to creative a gap below the endcap for the sawblade to pass through.Then I ran the circular saw along the level for a straight cut. Straight as an arrow, and it met Pretty Handy Dog’s approval.

Cutting out the backing design and painting:

Materials:

  • Dremel Trio
  • Palm sander
  • Sandpaper (100 grit & 220 grit)
  • Scrap 2×4 lumber
  • Chalk or pencil
  • Wood putty
  • Putty knife
  • Primer
  • Paint (white and navy blue)
  • 3M Clean Edge technology painter’s tape
  • Newspapers
  • 2″ paint brush
  • Small paint roller and tray

Sketch out the design on your bookshelf (using chalk or pencil) before beginning.

Before using any new power tool, take some time to read through the manual.

To insert a bit into the Dremel Trio, you push in the blue (shaft lock) button on the front and use the enclosed wrench to loosen the collet nut on the tool.

Insert the cutting bit into the Trio. (The trio also comes with a sanding drum bit and a routing bit!)

Tighten the collet nut with the wrench.

Turn the blue handle on the side of the TRIO to raise or lower the base plate.

Adjust the base plate until the cutting bit extends slightly below the wood backing of your bookcase.

Lay the bookcase down on its back. Position 2×4 boards under the edges of the bookcase (or you will be cutting into concrete. I’m pretty sure the TRIO is not capable of that, but I could be wrong.)

Plug in your Trio and get ready to have some FUN! You may want to practice on a scrap piece of wood before working on your bookcase. The TRIO allows you to change directions quickly and easily. Creating fanciful cuts is a breeze!

Squeeze the trigger and when the bit reaches full speed you can plunge it into the workpiece. For the pin holes hold the Trio steady, insert the bit and then lift it back out of the same hole.

To cut trees and other designs, plunge the TRIO into the wood and then slowly move the tool through the wood to carve your design. Be wary of long “V” shape cuts as they will make the backing weaker.

When your design has been completed, use the power sander to sand the back of the bookcase (where the majority of the splintering will have occurred.)

Insert the sanding drum bit into the TRIO and sand any large cut out areas.

Fold a piece of sandpaper in half and feed it through the thin lines of the branches to sand any rough edges that can’t be reached with the sanding bit.

Set the bookcase upright and inspect the cuts for more splinters. You can preview what your design will look like when lit up. Lookin’ good, huh?!

Before sanding the rest of the bookshelf, repair any dents or holes with wood putty. (This is a post I wrote about repairing all types of holes if you need help.)

Use the palm sander and a fine grit (220 grit) sandpaper to rough up the rest of the bookshelf.

Apply a coat of primer to the bookcase, shelves and sides. (Still working on emptying that can of KILZ Clean Start primer! Love that stuff.

When the primer has dried, mask off the sides of the bookcase where they meet the back.

3M sent me this Scotch Blue Painter’s tape with Edge-Lock protector to try. I was skeptical, but when I pulled the tape off it did give me a clean edge. The only place I had a little bit of seepage was in the corners where I didn’t press the tape tightly into the corner. The key to using this tape is to firmly press the edges with your finger to engage the “Edge-Lock” seal. I haven’t tried it for painting walls, but you better believe I have a wall project coming up that I can try it on.

Paint the back of your bookcase. I chose a very dark navy blue. To save paint, I used a medium blue paint for my first coat to darken the back and hopefully save paint.

Then paint one coat of the navy blue.

Follow up with a second coat to eliminate any streaking.

When the navy paint has dried, tape along the edges of the navy blue backing, where it meets the sides. Slip pieces of newspaper underneath to catch any paint splashes. (Will you get a load of my lazy supervisor! You think he’s been working hard in the heat? Uh no, that would be me doing all the work and him snoozing away the day.)

Paint the rest of the bookcase, the sides and the shelves white. I used two coats of Benjamin Moore Impervo Semi-gloss white.


Once the paint has dried completely, re-assemble the bookcase. And screw the end cap halves onto either side of the bookcase.

I installed a light rope behind the bookcase (tutorial to come at a later date) and set the lights on a timer. The rope light comes on at dusk and illuminates all the cut outs.

There is a very soft glow emitted from the back of the bookcase.

It provides the perfect amount of light for my son who HAS to have a light on at night.

My only complaint about the rope lights is that they give off a strong plastic odor. But, after a week the smell has dissipated.

I had the foresight to purchase a few of the clear display stands that slide into the end caps of the bookcase. It makes it easy to display books to pique my son’s reading interests.

Oh look! There he is now! Mission accomplished, reading interest piqued. Yes, I think he is double-jointed and a teacher pointed out that both my son’s sit like that. Must be in the genes.

A few more detailed pictures of the bookshelf. This has to be one of my favorite projects I’ve created recently. And it wasn’t very difficult to complete.




 

 

 

While sanding down my garden bench, I decided to make a design change. I chose to saw off the ball finial posts that are at the end of the armrests. I felt they were too tall and since I’m moving my bench onto our screen porch I didn’t want them obstructing the view if I was sitting with friends and chatting. So, I decided “Off with their heads!”

It was also the perfect opportunity to try out a new handsaw that Irwin sent me to test. They claimed that it is up to 3x faster than a traditional handsaw. Honestly I didn’t believe the claim. I mean – come on – a handsaw is a handsaw.

So, I decided to put their claim to the test with a good old fashioned match up.

The competition:
In this corner we have the challenger: the 15″ Irwin Universal Handsaw.

And the reining champion in this corner is my trusty handsaw.

Let me back up and tell you that I have a like/hate relationship with that traditional handsaw. I bought it a long time ago before I could afford a compound miter saw (power tool). So, I bought an el cheapo plastic miter box to use with it when I wanted to cut perfect angles. It took me about a dozen times before I learned how to properly use the hand saw. The key is to let the saw do the sawing (well, duh, right?!) Trust me, it isn’t as easy as it sounds. It is so tempting to press into the wood. But, if you put any force or pressure on the saw, it will skip and bind. Instead you have to gently push and pull the saw back and forth a gazillion times until the saw works its way through the wood. It can be  a brutally slow process.

So, back to the match up. I started with my traditional handsaw and started the timer.

About halfway through I had to take a break (and a picture). I gulped down some more coffee and continued sawing. (I stopped the clock at 1:15:20 when I took a break and restarted it when I began sawing again.)

Finally at 2 minutes and 32 seconds the ball finial met it’s demise and toppled to the ground. I wanted to topple down with it, exhausted.

I resisted the urge to go grab one of my power tools for the other side, but instead picked up the Irwin Universal Handsaw.

The angled handle felt a little strange in my hand (not bad, just different from the traditional one I was used to.)

I set the blade against the base of the post and began to saw. It cut through the wood easily and within 32 seconds it had lopped of the head of the other post. I was amazed. I double checked my timer, but it was working. Only 32 seconds and I was barely breathing heavy!

AND THE WINNER IS:

The Irwin 15″ Universal Handsaw by a longshot!

Here are a few details about the saw: It has a triple-ground tooth design, I’m guessing this has something to do with its speed. And the unique angled handle combined with the tooth design is supposed to eliminate binding. I had no binding, so it appears to work.

There are 45º and 90º angle markers built into the blade. I’m not sure that I would use them instead of my carpenter’s square, but I suppose they are convenient to have in a pinch. With a retail price of $18.99, the 15″ Irwin Universal Handsaw is a great and economic addition to your toolbox. (Especially if you can’t afford a power miter saw).

I’ve decided to send my traditional handsaw packing to make room for the Irwin Universal handsaw in my toolbox. Anyone want a gently used traditional handsaw for cheap?

Disclaimer: I was not paid for this review. I was sent the Irwin Handsaw at no charge, but the opinions and testing were my own and were not influenced by Irwin or anyone else. For more information you can view my disclosure statement HERE.

Recently I was asked what my favorite tool is. My Ryobi 12 volt Lithium Ion battery cordless drill was the first thing to pop into my head. Barely a week passes that I don’t reach for my drill to assist with a few loose screws (not that I personally have any of those.) For a homeowner or DIYer, this tool is indispensable. It allows you to drill holes, remove or drive screws and – well – just look like you know what you are doing.

I don’t just like this power tool, I love my cordless drill! Shhhh, don’t tell Pretty Handsome Guy, he might be offended. My drill is my right hand man, helping me breeze through projects with power and speed.

About 15 years ago my father-in-law asked what I wanted for Christmas, and I boldly told him that I wanted a cordless drill. He kind of chuckled and said, “Heh heh. Okay.” You see we didn’t own a house at that time, and I was still a young woman in my 20’s. But, I had big DIY dreams and I knew I wanted a power tool.

Christmas morning I opened a present to reveal a brand new 18 volt Ryobi Cordless Drill. It had loads of power, two torque settings and the whizzing whir that made me feel like I was one mean carpenter! Plus, it came with a flashlight attachment that would make any nighttime lurker look like a deer caught in the headlights.

I have owned two more Ryobi cordless drills since that Christmas present. The first one had to be replaced when the battery no longer held a charge (and buying a new battery cost almost as much as a new drill.) The second one met its demise when I accidentally drove a screw right up against a fence post and didn’t notice that the chuck was winding the opposite way until the collar was stuck wide open.

So, it was back to my super box home improvement store to shop for a new drill.

As I was checking out the drills and learning about the merits of the lithium ion batteries, I asked about the voltage difference since I had been using a 14.4 volt drill. The salesman at the “Big Orange” told me that I wouldn’t notice the difference between a 12 volt and a 14.4 volt. Pisshwah! I did notice a difference, especially when trying to drive screws into hardwoods! (My DIY abilities are sometimes underestimated by a few.) But, the salesman was correct, under normal daily use I don’t notice the difference.

Two things that I DO really love about this new Ryobi 12 volt Lithium Ion drill:  

1. Battery Life: Yes, yes, yes! What you have heard is true. The battery does last much longer. I’ve told you how much I use my drill, and I have only charged the battery on this drill three times since January 2010. That is 11 mos. of use including laying a sub-floor in our living room. The only downside to the lithium ion battery (but also could be considered an upside) is that the drill doesn’t slow or lose power until a few seconds before the battery is dead. Therefore there is very little warning that the battery is about to give up. At least this drill comes with a spare battery, so I always keep it charged.

2. Size and weight: 3.5 lbs. of cordless drill made me feel like I had some serious power in my hands! That is how much the old 18 volt Ryobi weighed. When I held the new 12 volt Ryobi drill, I embraced the lightness of its lithe 1.8 lbs! I can really appreciate the difference when reaching overhead to use the drill. Plus, this new drill with its smaller size and smaller grip fits perfectly in my hand.

As you can see below, my drill shows signs of being loved used frequently. But, it still works like the day I lifted it out of the box.

Some other features about this little green mean machine: 

It comes with a charger, extra battery, a phillips and flat head bit. There is a magnetic bit shelf right above the battery. And a canvas storage case. But, my drill doesn’t get that much time stored away. It usually rests right here…

…ready to leap into action at a moments notice.

If you don’t own a cordless drill, I implore you to add this DIY essential to your holiday wishlist!

(I was not paid or compensated to write this post. This is my honest opinion and true feelings about my beloved cordless drill!)

 

When I was 18, and bought my first car, and thought I was the coolest girl in town with a little zippy sportscar – sorry, just a little trip down memory lane.  My parents gave me my first tool kit. That tool kit is still with me today and I do use it a lot. The set has a series of sockets, crescent wrenches, interchangeable screwdriver bits, allen (hex) wrenches, needle nose pliers, and locking pliers.
 
That set got me through several repairs (both auto and home). Now, as a homeowner, I have found that there are a few more tools to have on hand.
You will likely want to look for a multi-piece set like this one:
This will give you a wide variety of tools for a low cost. If you want a deal, try shopping for these sets around Father’s Day or Christmas. The set above was listed on Amazon.com for approximately $50 – $60.
Regardless if you are buying these items in a set or separate, these are the tools I recommend:
Homeowner essentials:
  1. Hammer
  2. Screwdrivers – Phillips head and a flat (straight or slotted) head. Try to buy a small and medium size of each.
  3. Allen (Hex) Wrenches in several sizes
  4. Adjustable Crescent Wrenches – I suggest buying at least two. One 6″ and one 10″
  5. Slip Joint Pliers (handy for overall gripping)
  6. Needle-nosed pliers
  7. Vice grips (Locking pliers)
  8. Tape Measure
  9. Level – 24″ is preferrable
  10. Utility knife (mat knife)
  11. Safety glasses
  12. 12″ Handsaw
  13. Stud Finder
  14. Flashlight
  15. Pry bar (must have a flat sharp side and the other side a notch for pulling nails.)
  16. Tool box or case to keep all of the above in 
  17. My favorite DIY guide to my home: Home Depot’s Home Improvement 1-2-3 – the best $15 I ever spent!
 Screwdriver bits:
 

Last but not least, the most indispensable tool I’ve ever owned:
Cordless Drill with screwdriver bits and a small set of drill bits 

For Electrical DIY:
  1. Wiring instruction book or guide
  2. Wire Cutters/Strippers
  3. Electrical Current tester 
    • You only need the simple tester with two probes and an indicator light to test if the power is on. 
For the committed DIYer:
  1. Palm sander
  2. Carpenter’s square
  3. Staple gun
  4. Power Circular Saw 
    • Be sure to hold one in the store and feel how the grip feels in your hand. This is especially important as a woman with a smaller hand size. (more on power tool shopping in another blog post – coming soon!)
  5. Jig Saw
  6. Saw Horses or Folding Work Bench
  7. Clamps – A Variety of Adjustable Clamps and Clips

I hope this list gives you some good information so you won’t feel overwhelmed when buying tools. Definitely ask a sales person for help or opinions. Don’t tell them you are new at this. Ask them for the tool they would purchase if they were buying one for their shop. You should aim to buy a quality tool (especially power tools) that will last your lifetime. A cheap tool will either break or not have the power to do the job you need it to do. However, you don’t need to buy top of the line or break the bank to get a good tool.
Savings Tip: Many of the big box home improvement stores will usually price match tools that are priced cheaper at a competitor if it is the same make and model, plus take 10% off the price. Be sure to bring the ad with you or they will need to call or look up the price online.
 
Home Depots price guarantee:  
NOBODY BEATS OUR PRICES
If any competitor tries, we’ll beat their price by 10%. Guaranteed.*
*If you find a current lower price on an identical, in-stock item from any retailer, we will match the price and beat it by 10%. Excludes special orders, bid pricing, volume discounts, open-box merchandise, labor and installation, sales tax, rebate and free offers, typographical errors and online purchases.
Lowe’s price guarantee:
Everyday Low Prices, Guaranteed
We guarantee our everyday competitive prices. If you find a verifiable lower everyday or advertised price on an identical stock item at any local retail competitor that has the item in stock, we’ll beat their price by 10% when you buy from us. Just bring us the competitor’s current ad or we’ll call to verify the item’s price that you have found. Cash (charge card) and carry purchases only. Competitor’s closeout, special order, discontinued, clearance, liquidation and damaged items are excluded from this offer. On percent-off sales, Lowe’s will match the competitor’s percent-off offer. Limited to reasonable quantities for homeowner and one-house order quantities for cash and carry contractors. Current in-store price, if lower, overrides Lowe’s advertised price. Price guarantee honored at all Lowe’s retail locations. Labor charges for product installation are excluded from our price guarantee offer in our stores with an Installed Sales Program. Visit store for complete details.
Sear’s price guarantee:

If you find a lower price on an identical branded item with the same features (in Home Electronics identical brand and model number) currently available for sale at another local competitor retail store, Sears will match that price plus, give you 10% of the difference. Just bring in the original advertisement to a sales associate at the time of, or within 14 days after, your purchase. More fine print…

Happy Shopping!

 
 
Â