Hallway Storage – the Tutorial
After working on this tutorial for what seems like days, I finally have the Hallway Storage tutorial for you!
Thank you all for being so patient. We’ve had a busy week at the Pretty Handsome Home. Lots of wood rot and drainage problems being addressed, plus an emergency trip to the pediatric dentist. (Warning: Look away if a chipped tooth and bloody lip might make you faint.)
Luckily, all is moving in a positive direction right now (teeth and home repairs).
Materials (to the best of my recollection):
2 – 1 x 10″ x 12′ pine boards (and had Lowe’s cut them in half leaving us with 4 – 1×10″ x 6’s)
3 – 1 x 10″ x 8′ pine boards
1 – 1 x 15″ x 8′ pine board (had Lowe’s rip it to 13″ wide)
1 – 1 x 15″ x 4′ pine board
2 – 4′ x 8′ pre-primed masonite bead board sheets (cut to size by Lowe’s)
1 box of 2″ screws
1 box of finish nails (used 1 1/4″ finish nails in my pneumatic nailer)
6 – 1″ x 2″ x 8′ pine edging strips
1 – 8′ piece of decorative shelf moulding
1 – 8′ piece of trim moulding for the top shelf
Primer
Paint (white for unit, aqua color for behind cube towers)
Caulk
Wood putty
Sandpaper
Triple Coat Hooks (eBay)
Baskets (Home Goods)
 |
| Checking out with our 3 helpers leading the way. I hope they have their allowance to pay for all this! |
Building the cube towers:
I mentioned that the hall storage cube towers were built using Ana White’s Land of Nod cube tower knockoff plans. Ana’s towers are 17″ wide by 13″ deep and 70″ tall. We shrank Renee’s to 15″ wide and 10″ deep to accommodate her narrow hallway. And we eliminated the top and bottom shelf and legs. So, if you want the tutorial for the towers, head over to Ana’s site.
Here are two pictures of the towers after construction (before priming and painting):
 |
|
|
 |
| We took the towers inside to make sure they would fit. While they were in Rene’s house, I traced the profile of the baseboards onto each tower. You can see how to trace profiles in this older post. Plus, we marked where the towers would fit against the wall (so Renee could see where to paint the wall.) |
 |
| See, perfectly traced profile! |
 |
Building the shoe storage bench:
Our space dictated a narrow and shallow bench so as not to impede the traffic flow in Rene’s hallway.
Then drove the screws in to secure the shelf
Next I nailed the third board on top of the front side so I had a double thickness of 1″ x 2″ boards.
decorative shelf moulding below them (also cut to 30″ wide).
Finally we cut a board for the bench top: 1″ x 15″ x 30″. And our bench is essentially finished! (We left the top off until after the bench was attached to the cube towers and the wall.)
Installing the towers and bench:
After the towers and the bench were primed and painted with two coats of paint, we transported them back over to Renee’s house.
Renee had pre-painted the wall a pretty turquoise color at the back of the towers.
Now it was time to go stud hunting finding. I rely on two techniques for finding studs (and neither of them requires going to a singles bar!) First, I used my electronic stud finder. It takes some patience, but it gives me a good idea where the studs might be. To use the stud finder, I squeeze the buttons on the side of the gadget. Then s-l-o-w-l-y move the finder left and right over a 1-2 foot wall section. The light comes on when it detects something solid behind the drywall. Then I made a mark in the middle of the “lit” area.
Next I use the knocking technique. It almost helps to close your eyes for this. I will knock along the wall moving left and right. I’m listening for the knock to get higher pitch and sharper where the stud is. I can also feel less give in the drywall and it almost starts to hurt my knuckle because I’m knocking against a hard area where the stud is. You will most likely need a little practice to get a feel for finding the studs while knocking. Anyway, this gives me the idea where the studs are.
I’ve heard of using a third technique. Once you think you have located the stud. You can take a quilting pin and insert in into your drywall. If it goes in about half an inch and stops you have located a stud. If the pin can be inserted all the way to its head, you have hollow wall behind the pin.
Now that we had located the studs in the wall, we checked them by measuring between the studs. They are normally 16″ from stud to stud. And there should be a stud around the door and window frames.
So, the studs have been found and marked. Next we cut four 15″ lengths of the 1″ x 2″ boards and painted them the same color as the turquoise wall. These will be our cleats for attaching our towers to the wall.
Then pre-drilled holes on the cleat where at least one stud is. Lined the cleat up with the top edges of our cube tower. Then drove the screws through the 1″ x 2″ cleat. The second hole was not into a stud. We decided not to use a wall anchor because there was enough strength from the one stud and drywall.
Cutting a Hole for an Outlet:
Here is an easy trick for marking where to cut a hole in your bead board. In our case, we had to cut a hole for an outlet. 1. Take the cover off your outlet. Use bright red or dark lipstick and rub it on your outlet. 2. Set your bead board in place on the wall and press in where the outlet it. When you remove it, you will have the outline of your outlets. 3. Use your outlet cover and line it up with the outlet. 4. Then trace around the cover.
We cut our hole slightly smaller than the outlet cover. After you put the cover back on, wipe off the lipstick.
Then, we installed two more cleats though the bead board and at the same height of the bench. Sliding the bench back against the cleats, I used a few finish nails to nail the back of the bench to the cleats.
Before we put the bench lid on, we installed the second cube tower using two more pre-painted cleats in the same manner as the first tower. Then nailed through the sides of the bench and into the towers on each side.
Finally, we lined up the top of the bench and nailed it down into the wall cleats and into the bench sides and front.
The next step was to nail a 1″ x 10″ x 60″ board to the top of the towers and nailed down into the wall cleats to secure it to the wall. We added some decorative trim to the top board.
We cut a 1″ x 3″ x 30″ strip of wood to mount the coat hooks on. We also cut some more decorative shelf molding and attached it just under the top shelf and above the 1″ x 3″ hook board. Next we eyeballed our hooks and screwed them into the 1″ x 3″ boards.
To finish the built-in unit we caulked all our seams and filled the nail holes with putty. More details on this final step can be viewed in this post. Then covered the dried caulk and putty with paint.
Approximately $300 (including the baskets & hooks) and 3 days of work produced this fabulous organizing built-in hall storage unit! You can see some of the close-up pictures in this previous post.
What do you think? Not too hard to create, was it? A little over a weekend and Renee had a storage system for her entry hallway. I can’t tell you how much our mudroom bench has saved my sanity
I can't wait to try this out!!
Reread this today, your directions are terrific. Thanks! Ann
Kristin,
I don't see why not. You might have to rearrange your shelving to meet your needs. You may also want to take a look at my tutorial for turning a closet into a reading nook (posted in June.)
Good luck!
Do you think that I could use this in my closet as well?
Thank you so much for this great tutorial! I have to find a spot to put something like this 🙂
You should start your own business as a handy woman. You are unbelievable what you can do.
WOW, this is impressive. I think this looks even better than the "systems" they sell at Pottery Barn! Way to go!
It looks great! And thanks for such a great tutorial! I'm gonna go try and persuade my husband to let me do this now;)
I wish I could just snap and *POOF* you would be at my house building one of those…but smaller…much smaller. I have a split foyer, which means shoes, backpacks, violins, etc. everywhere(including the steps and banister.) Drives me crazy because I can't keep it from looking cluttered! Great job! Thank you for posting the tutorial!!!
I wish I would have had something like that when my 4 were little…it's fabulous! Great tutorial!
Beautiful!!! This is a fantastic tutorial! Great job – I have to share on my FB Page!
Fabulous tutorial, Brittany! And, please say that was his baby tooth? I knocked out my permanent tooth as a kid…
this is awesome!
You are amazing to put this tutorial together! I just love the end result. Wish I had your SKILLZ!!