Fixing Common Door Problems
, , , ,

Fixing Common Door Problems

Do you have a door that sticks or doesn’t close properly? You are not alone. Many factors can contribute to this problem. Let’s learn how fixing common door problems can be easy.

Fixing common door problems pin this image

Fixing Common Door Problems

Do you have a door that sticks or doesn’t close properly? Or maybe your door rubs, squeaks, or is drafty. Regardless of the problem, I’m going to show you how to fix your most common door problems! But first, a big thank you to Schlage, the 100-year-old leading door hardware company, for sponsoring this article.

If you have common door problems, you are not alone. Many factors can contribute to them: house movement, humidity, dry air, improper installation, slamming doors, or kids swinging on them (true story). Without being able to control many of these factors, it’s important to know how to fix your door problems – as your door is often a main focal point of the room and/or entryway.

(I’ve included affiliate links for your convenience. I earn a small percentage from a purchase using these links. There is no additional cost to you. You can read more about affiliate links here.)

Door Not Latching:

A door that doesn’t latch properly is usually a simple fix. Lean down until you are at eye-level with your doorknob. Look at the gap between the door and the door frame. Is the latch centered on the strike plate?

latch too low on strike plate

If not, that’s why your door doesn’t latch. Here’s how to fix it. Determine the center of the latch. Remove the strike plate and move it to center on the latch.  Mark the new location of the strike plate. Chisel the door frame as needed.

chisel strike plate area out

Reattach the strike plate and test the door. You can see in the photo below the latch is now centered with the strike plate and the latch can now slide into the strike plate properly.

Latch and strike plate lined up

(Like the knob above? It’s a Schlage Plymouth in Bright Brass, but comes in a variety of finishes.)

Door Not Closing Tight Against Stop:

If your door rattles loose in the frame and doesn’t close properly against the stop, it can be as simple as moving the strike plate closer to the stop.

Important: If this problem happens on a door between the garage and the house, it could be a potential safety issue! The door between the garage and the house must protect the residents from carbon monoxide gases potentially leaking in from a car’s exhaust. With this in mind, it’s important to fix this problem immediately!

Luckily, fixing a door that doesn’t close tightly is a simple one to remedy. But, there are two solutions depending on your type of strike plate. (Is your strike plate adjustable or non-adjustable?)

door won't shut tight vs. door closes against stop

If You Have an Adjustable Strike Plate:

Look closely, does your door strike plate have a small screw holding a sliding tab to the strike plate? If this looks like your strike plate, the solution is simple.

common door problems strike plate

Loosen this screw and adjust the tab closer to the door stop.

door problems adjust latch

Tighten the screw and try closing your door again. Continue to adjust the tab until your door shuts properly and stays closed.

If You Have a Non-Adjustable Strike Plate:

Non-adjustable strike plates don’t have an adjustable tab, but your fix is still easy. Remove the strike plate and reposition it closer to the stop.

moved strike plate

Sticking Doors or Doors that Won’t Close

Look at the space around the door. Is there a gap at the top or bottom? Normally, the door will stick at the top corner opposite of the hinges because over time the weight of the door will pull away from top hinges.

To fix a door that sticks or rubs in the frame, you can try one of these fixes:

  • Tighten screws
  • Add longer screws
  • Add a shim behind a lower hinge

Let’s take a look at this french door. The door rubs at the top when trying to close it.

french doors rubbing at top

Open the door and look at the hinges. Do any of them need to be tightened? Well look at that! This door is missing a screw.

missing screw in hinge

Try to tighten the screws. If they just spin, the wood has been stripped. You can either add longer screws or fill in the holes with toothpicks.

Replace with Longer Screws

Remove the hinge screws and use longer screws that drive through the door jamb and into the framing.

long and short screw in hand

How to Fix Stripped Screw Holes:

Remove the screws from one hinge at a time. Squeeze some wood glue onto several toothpicks. Pack the hole with toothpicks.

insert toothpicks into stripped screw holes

Let the glue dry. Cut off the excess toothpick with a utility knife (or use a chisel if you don’t have your knife with you.)

chisel off extra toothpick

Drive screws back into the hinges.

drive longer screws into door hinge

Better yet, replace the screws with longer ones that will grip into the framing behind the door jamb.

Hopefully this will fix your door. You can see below the door shuts and the spacing is even between the french doors.

Is Your Door Out of Alignment?

Door still rubbing? Occasionally a door will get out of alignment. To fix this, first, look at the door and determine where the gaps are bigger.

For the door above, try simply loosening the screws from the top hinge 1/4 turn or more. If this doesn’t work, try tightening the screws into the hinges at the bottom. If it’s still not fixed, you’ll need to try shimming the door hinge.

Shimming Door Hinges:

Sometimes a door hinge needs to be shimmed to adjust the door in the frame. If the spacing is tight behind one hinge, you can adjust it slightly to correct uneven spacing around the door.

common door problem fixes

The door above still shows a tight spot near the top right hinge. To shim it slightly, add a piece of chipboard (cereal box cardboard) behind the hinge.

door problems shim hinges

If you need a thicker shim, you can use the end of a wood shim.

add shim behind hinge

Replace the screws in the hinge and test your door. Is it still rubbing?

replace door hinge screws

Recessing a Hinge:

Occasionally, you might need to set a hinge deeper into the door or the frame. You can use a chisel to remove a small amount of material from the jamb or the door. If you don’t have a chisel or are worried about taking out too much, use the small sanding bit on a Dremel.

dremel door hinges

Door Rubbing on Top:

Have a door that swells when the temperature or humidity changes? To fix a door that rubs along the top in different seasons, you’ll want to sand or plane the top. This doesn’t involve buying a ticket or boarding an airplane. Planing is removing material from the edge of wood. You can try using sandpaper with a coarse grit to sand it down, but if that doesn’t work, reach for a hand planer.

plane top of door

As you run the planer across the top of the door it literally shaves off some of the wood. Simple design, but very effective.

Door Scraping on the Floor:

door scraping floor

A door that rubs on the floor or carpet is not only annoying, but it can scratch your floors. Time to fix this problem!

Get a helper to assist with removing the door. Close the door completely.

Position a scraper or flat pry bar just under the hinge pin head. Gently tap the end of the pry bar with a hammer to raise the hinge pin. Remove the hinge pin from the top and bottom hinges first.

remove hinge pin

Remove the middle hinge pin last but have your assistant nearby to hold the door in the frame. As the assistant opens the door, be ready to lift it off the hinges.

Lay the door on sawhorses. Tape the button of the door with painter’s tape to protect from chipping.

cut off bottom of door

Use a circular saw, track saw, or power planer to remove a portion of the bottom of the door.

Plane doors from the edge to center

Replace the door and check to see if it still rubs.

Exterior Door is Hard to Open:

If your exterior door is hard to open, it might be from a loosened threshold piece. You can try to tighten the threshold screws or replace the threshold and sweep at the same time.

driving screws into door threshold

Also check to see if the door sweep has lowered. Unscrew the sweep and raise it on the door. Tighten the screws.

raise door sweep

Door Latch Sticks in the Door

If the latch is sticking in the door, you can try one of three fixes:

  • Loosen the screws on the doorknob. (Tightening the screws on your doorknob too much can cause the knobs to bind.)
  • Remove the knobs, spray a little lubricant onto the latch inside the door. Replace the knobs and turn them to distribute the lubricant.
  • Finally if all else fails, it might be time to replace the doorknobs. Believe it or not this is a quick fix and can be done in five minutes.

Save yourself the headache of doorknobs that stop working smoothly and purchase Schlage brand door hardware from the start. Schlage has been producing high-quality door hardware in a variety of types, looks, and finishes for more than a century and will continue to do so in the years to come. Whether traditional, modern, or technology, Schlage products offer a limited lifetime mechanical and finish warranty and a three-year limited electronics warranty.

How to Replace Door Knobs | Pretty Handy Girl

Squeaking Doors

Doors that squeak mean the hinges need lubrication. Simply spray a lubricant like WD-40 just under the top of the hinge pin. Be sure to have a rag handy to catch any drips.

Fixing Common Screen Door Problems | Pretty Handy Girl

Open and close the door several times to help the lubricant work its way down the hinge. Your door should be squeak free now.

Door Knob Hits the Wall

Door knobs that hit a wall can put dents or holes in the wall if left alone. The solution is quick. Either add a door stop behind the door at the baseboard…

door stop behind door at baseboard

…or add a hinge pin adjustable door stopper to the top door hinge.

hinge pin adjustable door stopper

Drafty Doors

Cold drafts wafting in around your door? The solution is as simple as installing (or adjusting) the weatherstripping. If you can see light coming in around your door, it’s guaranteed to let drafts in too!

Adding Foam Weatherstripping | Pretty Handy Girl

Simply adding adhesive-backed foam weatherstripping around the door will stop those drafts in their tracks.

Look Ma, no more light, no more drafts!

Adding Foam Weatherstripping | Pretty Handy Girl

Adding a door sweep to the bottom of the door will keep out drafts from the bottom of the door. In addition, a well-fitted sweep will also keep insects and spiders from making an entrance under your door.

white door sweep on yellow door

That pretty much sums up fixing common door problems. Next time you have an issue with your door, you can fix it yourself!

PHGFancySign

Disclosure: This article has been sponsored by Schlage. If you’ve been around here for a while, you know I’m very particular about the brands I work with. I only recommend products and brands that I use myself. I was compensated for my time, but I was not told what to write. All opinions are my own.

Pin for later!

How to Fix common Door Problems

52 replies
Newer Comments »
  1. Lori
    Lori says:

    Hi My closet door suddenly won’t close on the opposite from the hinged side. It slightly hits the mouldings just at the bottom inch? How did this happen suddenly and how do I fix it?
    Lori

    Reply
    • Brittany Bailey
      Brittany Bailey says:

      Sounds like your door is warped. If it’s hollow core, try to place the bottom between your legs and have a friend or yourself pull the top in the direction you want it to move. If it’s solid, you could try moving the doorstop. Just remember you’ll have to re-caulk and paint.

      Reply
      • Dave Avella
        Dave Avella says:

        Door is solid. I just replaced everything ..think I didn’t put back together good. The frame standard 41/2. But I had to rip frame length to 21/2 to fit wall

  2. Joy
    Joy says:

    I’m a fellow handy girl and recently my door stopped latching. I inspected the hinges for loose screws and tried lifting up on the door to make it line up, no luck. It was fine for years so I’m puzzled about the sudden problem.
    Anyway, I read several how-to sites before I found your page. All were too basic or too specific (buy xyz type shim…print out template for strike plate [seriously??!!?] ). I *love* your cardboard shim tip…brilliant and simple; I’m going to try it out. Should have searched for another handy girl first! 🙂

    Reply
  3. Jason
    Jason says:

    Thank you so much , i loosened the hinge screws on the bottom of my bedroom door and it finally closes again…. Great tutorial and advice, i had been looking to fix this for about a year lol (its fine in winter, summer it will not close !!) Really appreciate it !! J, Canada !

    Reply
  4. Bob
    Bob says:

    a while back my daughter was playing with my bedroom door and now, we have to push in order to close it and it wont open anymore, to open it we need to get some tools and open it because the metal thing that moves in and out when you open it, it doesn’t move and sometimes we’re stuck in there, PLEASE HELP

    Reply
  5. Dina
    Dina says:

    Thanks so much!
    You just helped me fix my doors that have been ‘off’ for months since having to take them off the hinges.
    Wooohoo!!! And I did it myself! 🙂
    Pretty handy girl ‘high five!!’

    Reply
  6. Margaret W
    Margaret W says:

    My dog has separation anxiety and my mom dementia. She has accidently closed him in rooms while I was at work or out mowing the yard and he has promptly dug his way through the door. I bought a replacement door at local store, they took the old damaged door and cut exact “supposedly”. But now I’m finding it doesnt close. I tried your tip of dremel to get the hinges in farther as I could clearly see the gap of about a 3/8ths inch on that side. The hinges are now laying very flat in there, but still there is decent size gap, about half the size as before but the door will not close. I’ll have to plane quite a bit to close it. What I dont under stand is, I have the old door and measuring down, this door is exactly the same size! So its something to do with that side how the gap between hinges. Any thoughts? We did use the old hinges from original door. I have 3 more to replace and am not looking forward to this nightmare on each one.

    Reply
  7. The Vintique Object
    The Vintique Object says:

    I always appreciate a useful post like this. I recently jammed roll of socks in the crack of my girls’ door to keep it from slamming shut on little fingers. Now the darn door doesn’t close without some serious shoving. I’m going to inspect it now for cracks and tight spots. Thank you!

    Reply

Trackbacks & Pingbacks

  1. […] Pretty Handy Girl – There are quite a few helpful pictures on this page showing the various aspects of adjusting a door that doesn’t fit properly […]

  2. […] your issues. If your door is still sticking, you may have to take more drastic measures like routing out more material from the door frame with a Dremel or using a power planer to trim down your […]

  3. […] Bed, 100[/phpbay] what are the specifics for adjusting the bed on a 03 silverado? on impact it might of got off set 2 …easly twist it streight unless you bent the frame EZ Adjust Bed Rail, Promote senior care with Bed […]

Newer Comments »

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.