Curbside Vintage Step Stool Makeover
A few years ago, while driving back to work from my lunch break, I spied a very cool but sad looking vintage step stool sitting at the end of someone’s driveway next to their trash. I passed by, but it didn’t take me long to circle around the block and come back to pick up the stool. Unfortunately the step stool stayed untouched for at least 4 years. This time it wasn’t in my garage, I left the sad step stool in the back room of my office. Good thing I’m the only one who goes back there! I finally decided it was time to show this little vintage step stool some love. Check out this step stool makeover.
The structure of the step stool was in fairly good condition, but COVERED in rust. In some areas thicker than others. I thought about using the old school method and hand sanding the stool like Jeff talked about a few weeks ago (Painting Metal Patio Chairs ) but decided if I tried this avenue I would be sanding for a few months. I also considered using a sand blaster to remove the rust. And while it is a fast effective method, it is not practical for everyone. After much thought I finally decided on a 3M sanding disk that attaches to any drill. Let’s get to it shall we?
Step Stool Makeover MATERIALS
– Painter’s Tarp
– Spray Paint (Valspar – Golden House)
– 3M Paint & Rust Stripper Drill Attachment
– Painters Tape
– 1/2 yd of Mariners Fabric
– Decorative Upholstry Tacks
– 3/4″ Plywood
– Flathead Screwdriver
– Pliers (optional)
– Jig Saw
– Hammer
– Drill
– Small Drill Bit (optional)
– Damp Cloth
– Safety Glasses
Step Stool Makeover Instructions:
Wipe down the stool (or whatever you are working on) with a dry cloth to remove any excess dirt or rust that might be chipping. Also remove the seat and back to your stool if applicable.
Attach the 3M Paint & Rust Stripper wheel to your drill. Start your drill and apply some pressure. The amount of pressure needed will be determined by the thickness of your rust. You should be able to tell how much you will need once you get started. Make sure to have your eye protection on when you start removing the rust.
Once the rust is removed you can test the smoothness of the metal by running your hand over it gently. If you find rough spots you can to back and take more of the rust off. Take a damp rag and wipe all surfaces on the stool including the step treads.
Continue prepping your stool for paint by taping off the treads with painter’s tape.
Apply a light coat of paint making sure to avoid any drips that can be caused by over-spraying the chair. Our stool took two coats to get complete coverage.
While your paint is drying, remove the fabric from your seat back. Use a flat head screw driver to get under the old tacks and pry them up. I could not find our small flat head so I used our irrigation head adjustment key (sometimes you just have to improvise). Use the pliers to pull the loosened tacks out.
Prep the fabric by cutting it 1 – 2″ wider than the outside of your seat. Start upholstering the seat by putting one staple in the center of one side of the board pull the fabric taught and add a staple to the opposite side. Continue down one side of the seat stopping about 1″ from the corner. Do the same to the opposite side of the seat.
Now you are ready for the corners!
1. Using your fingers to hold the fabric taut, create an ear like tab and add one staple to each side of the tab.
2. Hold the end of the tab and pull the tab flat to the back of the board.
3. Making sure to keep the fabric taut, add 1 – 2 staples to secure the corner.
4. Cut away excess fabric.
To cover all the staples, cut a piece of fabric roughly 1/2″ smaller than your seat. Use decorative upholstery tacks every few inches to hold the fabric in place. Keep in mind where the seat will be attaching back to your stool and make sure to leave adequate spacing for your screws or you will have to remove tacks to be able to re-attach the seat. If you use mariners fabric, you can leave the raw edge exposed since it won’t fray. Bonus, the fabric is waterproof and very easy to clean. If you are having trouble getting your tacks to go into the wood with out bending, you can pre-drill your tack holes. This will save you a lot of headache in the end!
The bottom seat of the step stool was beyond repair and rotted out. Using the old seat as a template trace around the seat onto a piece of plywood.
Use a Jig Saw to cut the new seat and upholster using the same steps listed above. When your seat is complete and the paint is dry re-attach your seat.
Can you believe this is the same stool?
The white and yellow really pop! The 3M paint and rust stripper disks really gave the vintage step stool a new life. I am still amazed at how smooth the finish came out!
I’ve been on the lookout for one of these. My grandma had one and we all used to fight over it as kids. I want to get one for my daughter. Love the makeover.
I’ve been seeing this all over the internet and absolutely love it every time!!! I totally want one of those chairs!
This turned out so cute Jacque! I love this stool and totally would have scooped it up.
Amazing! Fantastic job. We had one when I was growing up. I could really use one now. I’m only 5ft. tall!
We used to have one of those chairs when I was growing up. It was my favorite chair to sit in. Can’t believe you found one. You did a great job!
Super cute!! I love the yellow that you chose. I can’t believe you sanded all that rust off! I would have just painted over it, but sanding it down really made all the difference. Good job! 🙂
Oh my goodness, I LOVE that stool, so jealous! What a great transformation!
It turned out great! Reminds me of the one in my grandmother’s kitchen, those were some great memories.
Great job girl! This looks amazing and you’d never know it was a curbside find!
LOVE this! My mother in law has one that I have been trying to talk her out of for years! Awesome job, Jacque!
I’ve always wanted one of those stools! they look so handy. That sunny yellow color is just perfect for the kitchen.
I always forget about those rust remover attachments for the drill and they are awesome!
Excellent stool. I love having those things around the house. They are so handy. I guess this means I have to start prowling the streets of my neighborhood to get my own.
Love to see you redo this project…my Nana had a stool just like that when I was growing up…it was my seat in her kitchen…love those memories – thanks for sharing!
Turned out very cute! I recently did a similar curb rescue makeover with a kids card table
Great project! I have the same type of stool, it came from my great grandmother. The 3M wheel is the HEAT!! Love those things!